By unit type
Speed limiters
Fitting a speed limiter - unlock it by serial number, link it to the tracker if it takes speed zones, then set and confirm the maximum.
A speed limiter is fitted as hardware and commissioned in the app, in its own flow. It has no SIM and no IMEI, so you unlock it with the serial number on its label rather than an IMEI.
Start it from Fit a speed limiter on the dashboard, not New Installation. The two flows ask for different things: a tracker needs its IMEI, a limiter needs its serial number.
No PIN on the work order? The limiter is unlocked with its serial number plus an 8-character PIN, the same way a tracker uses IMEI and PIN. The office can look the PIN up against the serial at any time, so ask them rather than guessing. The serial is on the unit’s own label.
The two kinds of limiter
Which flow you get depends on the unit, and the app works it out from the model. It matters because one of them cannot be finished on its own.
| Unit | What it does | Needs a tracker? |
|---|---|---|
| Takes speed zones | Holds the vehicle to the limit of whatever zone it is in | Yes - it takes those limits from the tracker |
| Fixed maximum | Holds the vehicle to one maximum speed everywhere | No - it can be fitted on its own |
The Model step tells you which one is in your hand. If it says Speed zones: Yes - needs a controller, the vehicle must already have a tracker fitted and commissioned before you can finish.
What the flow looks like
- Authorise - enter the serial number and PIN from the unit label.
- Model - check the unit on screen matches the one in your hand. Confirm with This is the unit.
- Customer - locked to the customer if the unit is already allocated, otherwise pick them.
- Vehicle - pick or create the vehicle. A vehicle that already has a limiter will not be listed.
- Fit - the fitting checklist for this unit. The steps change with the connection: an RS232 unit gets an RS232 step, a CANbus unit gets a CAN step.
- Link controller - only for a unit that takes speed zones. Pick the tracker you wired it to.
- Set limit - enter the maximum in mph, then read it back off the unit and confirm it.
- Done.
There is no check-in step. A limiter has no connection of its own, so it cannot report in. The fit and the confirmed limit are the evidence instead.
Linking to the tracker
Only for a unit that takes speed zones. A fixed-maximum unit skips this step.
The zone limits reach the limiter through the tracker, so the two have to be linked. The Link controller step lists only the trackers on the vehicle that can do this.
If it says No speed controller on this vehicle, stop. Commission the tracker first, then come back to the limiter. Fitting the limiter without the link leaves the vehicle with no speed zones and nothing to show the office why.
Setting and confirming the limit
You enter the maximum in mph. The unit stores it in km/h and the app converts, so enter the mph figure the work order asks for and nothing else.
Read the applied limit back off the unit and tap the confirm button. Setting a limit you cannot confirm proves nothing, so a unit that can report its limit back must be confirmed before you can finish. Change the number and the confirmation clears - read it back again.
Some units cannot report their limit back at all. The app says so and lets you finish, and the office sees the maximum marked as unconfirmed.
Troubleshooting
The serial and PIN are rejected. The message does not say which was wrong, on purpose. Check both against the label, then check the unit has not already been replaced - a decommissioned unit cannot be unlocked, because its serial may have been reissued.
The vehicle I want is not in the list. A vehicle that already has a limiter fitted is left out. If the old unit has been removed, the office needs to take it off the vehicle first.
“No speed controller on this vehicle”. The vehicle has no tracker that can carry speed zones, or the tracker is fitted but not yet commissioned. Commission it, then reopen the limiter install.
I cannot get past Set limit. Either the number is outside what this unit allows (the step tells you the range), or the limit has not been confirmed on the unit yet.
Related
- Unlocking a unit - the equivalent step for a tracker, using IMEI and PIN.
- Choosing the customer and vehicle - link the limiter to the right customer and vehicle record.
- Speed control - how the office sets up speed zones afterwards.